How To Cut Window Blinds That Are Too Wide
How to Cut Window Blinds that are Too Broad
What Can Yous Practise When Your Blinds Are Also Wide?
Horizontal shades are widely used in offices and homes for their functionality and versatility. They are effective in controlling low-cal, privacy, provide privacy and security and aslope this, the blinds add elegance and luxurious entreatment to your homes. These horizontal blinds come in all sizes and generally, it poses no difficulty in finding the right fit for your windows. Sometimes however there may be in error in measurement or come in a size that is a tad too broad for your windows. This does not mean that you need to render the blinds. You can cut them down all by yourself with little endeavour and some patience and your blinds will be set up for use.
Tools Needed
To cutting the width of your blinds to fit your windows you will need the following tools:
• Measuring tape
• Pencil
• Table saw
• Hacksaw
• Fine-tooth bract
• 150-dust sandpaper
• Rubber bands
• Masking tape
How to Brand the Cuts
Cutting the width of the blinds entails a number of steps and processes.
Trimming Head Runway
To get the perfect width for your blinds, your beginning task is to trim the headrail as it as well forms office of the width.
one. Take the measurement of your window and internet measure out the headrail. Deduct the width of the window from the width of the headrail. This will be the amount of inches/cm you will need to cut off.
2. Whatever measurement you get later on deduction, carve up that figure by 2 if information technology is more than two inches. Then yous will demand to cut ½ of the actress width from either side of the headrail. If information technology is less than two inch y'all can make the cutting from one side itself.
three. Now measure the headrail and make markings on one finish or on either stop using a pencil.
4. You volition discover a stiffener that is located at the end of the headrail. These are metal pieces that help to hold the headrail in a square position. You need to take these stiffeners out.
five. Use a hacksaw to cut the headrail along with the marks you lot fabricated. If the metallic headrail bends a little while cutting, bend them dorsum into position and replace the stiffeners.
Trimming the Blinds
Once the headrail has been cut it is fourth dimension to trim the blinds.
ane. Stack the slats up evenly. Make the ends affluent and do not exclude the bottom track though the latter volition be thicker than the slats.
ii. Use a prophylactic at each cease to tie the blinds tightly to go on them in an even position.
iii. Measure the window width and the blinds. Decrease the width of the widow from the width of the blinds. This will be you need to cut off. Irrespective of how small the cut, brand sure that you cut ½ of the measurement taken from either side of the blinds. Make sure that the strings controlling the blinds are evenly spaced from each side one time the cuts have been made. To prevent the blinds from chipping when they are being cutting y'all use masking tape at the cut lines. Utilise a table saw to cut the blinds but use only a fine-molar blade that is used for cutting finished wood. Use a carbide bract if there is any metal on the binds.
4. Cut the blinds carefully. Apply the bottom rails as well. Though thick, the headrail can be still cut with the saw.
5. Accept the masking tape off as likewise the rubber bands. For rough edges use the sandpaper to smoothen them out.
Trimming the Valance
Blinds often come up with a valance. A valance is a decorative slice of wood that is installed at the top of the windows to hide the headrail and ugly window treatment hardware. Many may choose non to opt for a valance but blinds that have a valance have to be cut besides. They are of the same width equally the blinds. When the blinds are being cut to shorten the width, the valance needs to be trimmed too to match the width of the blinds.
i. Measure out the valance. Use the aforementioned measurements equally the blinds; make markings on the valance where the cut will be fabricated.
2. Use masking tapes once again to wrap the cutting lines to prevent the valance from chipping when the cut is being made.
3. Use a saw to advisedly and slowly cut the valance.
Once the valance is cut your blinds are now completely fix for use. The headrail, slats and the valance is of your preferred width and brand a perfect fit on your windows.
Things to Remember
• Avoid ownership blinds that are as well wide for your windows. Though blinds can be cutting, if they are too wide you lot might terminate up cut very close to the strings when they are existence trimmed.
• Even if the headrail is not neatly cutting, do not worry. Your valance volition anyways hide them when they are installed.
• If your blinds are inside mountain so cut the blinds most ½ inch less than the width of insides of the window frame. Otherwise, the blinds will scratch the sides of the window frame.
Source: https://www.zebrablinds.ca/blog/how-to-cut-window-blinds-that-are-too-wide-02-2020-06/
Posted by: albashignigho.blogspot.com
0 Response to "How To Cut Window Blinds That Are Too Wide"
Post a Comment